如何用英文和老外检讨模具。
1． ***！你现在有空吗，我可以问你一些问题吗？
could i ask you some questions？may i ask you some questions (a question)?
2． 请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？
can you tell me whether the su***ce of this part is a visible/esthetic one? what will we do for its su***ce? texture or polishing?
3． 请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？
does this part need an ejector pin or an ejector bar? can we add an ejector blade?
4． 这个产品的柱位我们打算做司筒。（或镶针）可以吗？
can we add ejector sleeves or ejector pins in the boss of this part?
5． 产品的这个位置有倒扣不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
there's an undercut at this position that can not be molded, we plan to make a slider for it. it will also h**e a parting line on this side, is that ok?
6． 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？
we will make the lifter and (inner) slider in this position, will that be a problem?
7． 你提供的2d产品图与3d产品图不一致，请问以哪一个图面为准？
the 2d and 3d drawings you provided are not the same, could you advise which one is correct?
8． 你提供的3d产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。
there is no draft angle in the 3d model, some areas are too thick, and some are too thin. can we modify them by ourselves? we will send you the updated drawing for approval.
9． 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？
according to the shrinkage rate .005”, the mold has been done in the right dimension, but the part falls short to your part print(the actual dimensions are out of tolerances), are you sure the shrinkage is right?
10． 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？
this position is too small and will cause thin steel, can we widen it here?
11． 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？
the space(room) is too small between the lifter and the boss. the angular lifter interferes with the boss during ejection(when moving). please consider changing the position of the boss.
12． 这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？
the rib here is too thin and relatively high, so it will be difficult to fill(走胶) here during the injection process, can we increase the thickness of this rib?
13． 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？
are you going to increase or decrease the plastic(material) on this rib?
for increasing plastic, we will use edm.
for decreasing plastic, there will be two options. one is to make inserts; the other is to weld the tool.
because there is water line under the insert, is that ok?
14． 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
the bottom of the rib was burned due to poor venting, we can add an insert in the middle of the rib to improve it.
15． 重做镶件大约需要5-6天时间，你能接受吗？
it will take about 5 or 6 days to re-do the insert, is that ok?
16． 产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。可能需要几天的时间。
所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？
we h**e already textured this side. if we add material, it will take a few days to remake the texture. so we suggest using the edm( spark) finish instead of texturing, is that ok?
17． 模具是用公制/英制的配件？需要备用件吗？
are the mold parts in inches or mm? do they need spare parts?
18． 模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。
will you provide the engr**ing content of the mold label? please advise it asap.
19． 可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大小、呵林柱尺寸、顶棍孔尺寸等。
can you provide the specifications of your injection machine? such as the press size, tie bar space, konck-out( rods holes pattern.
20． 这个问题我需要同其它同事商议会再答复你。
i will discuss it with my colleagues, and reply asap.
21． 我们将尽力达成你的计划，如有异常，会及时通知你。
we will try our best to meet/ reach your plan. for any problems, we will notify you immediately/promptly.
22.这个产品的长度为330.12mm,宽度为78.
96mm,高度为45mm.胶厚为2mm,重量为70.63g,试模注塑机型号为250吨，胶料颜色为黑色，产品外表面晒纹处理，内表面为抛光。
需要日期章、环保章、材料章。前后模用2344氮硬，斜顶和行位座用738h，以上模具信息正确吗？请确认！
please check the information below and comment/approve.
l. w. h =330.12 x 78.96 x 45mm,
thickness - 2mm.
weight - 70.63g,
press size - 250t
color of the t1 samples - black.
outer/visible su***ce finish – texture; inner side – polishing.
date code, recycle stamp and material needed.
c** & core - 2344 nitrided steel; lifter and slider shelf/base/retainer - 738h.
23． 现在到了吃午钣的时间，我们下午再继续好吗？
lunch time, shall we go for lunch now? we can discuss the project later.
24.和滑块干涉的倒勾**料填平至滑块可以顺利滑动。
the undercut area interferes with the slide block, so we suggest adding material to help the slider move smoothly.
25. 加胶太多 (the added wall/thickness is too much)
26. 加肉面积太大 (the added area is too wide.)
英语100句
301.did you enter the contest?你参加比赛了吗？302.do you accept credit cards?你们收信用卡吗？303.don t cry over spilt milk 不要做无益的后悔。304.don t let chances pass by 不要让机...
英语100句
1。hello,may i could i can i speak to the manager,please?sorry,he is out.oh,just a minute,he is coming.您好，请经理接 对不起，他出去了。喔，请稍等，他回来了。2。hi,nice to meet yo...
英语100句
2.welcome to our school 欢迎来到我们学校！3.hello.你好。4.good morning afternoon evening 早晨好 下午好 晚上好！to meet you.见到你很高兴。to meet you,too.见到你也很高兴。are you?你好吗？thank ...