模具工程常用词汇

发布 2021-05-25 05:24:28 阅读 1322

common vocabulary for die engineering模具工程常用词汇

die 模具

figure file, chart file图档

cutting die, blanking die冲裁模

progressive die, follow (-on)die 连续模

compound die复合模

punched hole冲孔

panel board镶块

to cutedges=side cut=side scrap切边

to bending折弯

to pull, to stretch拉伸

line streching, line pulling线拉伸

engr**ing, to engr**e刻印

upsiding down edges翻边

to stake铆合

designing, to design设计

design modification设计变化

die block模块

folded block折弯块

sliding block滑块

location pin定位销

lifting pin顶料销

die plate, front board模板

padding block垫块

stepping bar垫条

upper die base上模座

lower die base下模座。

upper supporting blank上承板

upper padding plate blank上垫板

spare dies模具备品

spring 弹簧

bolt螺栓。

plate电镀

mold成型

material for engineering mold testing工程试模材料

not included in physical inventory不列入盘点

sample样品

incoming material to be inspected进货待验

description品名。

入水:gate

进入位: gate location

水口形式:gate type

大水口:edge gate

细水口: pin-point gate

水口大小:gate size

转水口: switching runner/gate

唧嘴口径: sprue diameter

二、流道: runner

热流道: hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道:round(full/half runner

流道电脑分析:mold flow analysis

流道平衡:runner balance

热嘴: hot sprue

热流道板:hot manifold

发热管:cartridge heater

探针: thermocouples

插头: connector plug

插座: connector socket

密封/封料: seal

三、运水:water line

喉塞:line lpug

喉管:tube

塑胶管:plastic tube

快速接头:jiffy quick connector plug/socker

模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

边钉/导边:leader pin/guide pin

边司/导套:bushing/guide bushing

中托司:shoulder guide bushing

中托边l:guide pin

顶针板:ejector retainner plate

托板: support plate

螺丝: screw

管钉:dowel pin

开模槽:ply bar scot

内模管位:core/c**ity inter-lock

顶针: ejector pin

司筒:ejector sleeve

司筒针:ejector pin

推板:stripper plate

缩呵:movable core,return core core puller

扣机(尼龙拉勾):nylon latch lock

斜顶:lifter

模胚(架): mold base

上内模:c**ity insert

下内模:core insert

行位(滑块): slide

镶件:insert

压座/斜鸡:wedge

耐磨板/油板:wedge wear plate

压条:plate

撑头: support pillar

唧嘴: sprue bushing

挡板:stop plate

定位圈:locating ring

锁扣:latch

扣鸡:parting lock set

推杆:push bar

栓打螺丝:

顶板:eracuretun

活动臂:lever arm

分流锥:spure sperader

水口司:bush

垃圾钉:stop pin

隔片:buffle

弹弓柱:spring rod

弹弓:die spring

中托司:ejector guide bush

中托边:ejector guide pin

镶针:pin

销子:dowel pin

波子弹弓:ball catch

模具工程常用词汇

die模具。figure file,chart file图档 cutting die,blanking die冲裁模 progressive die,follow on die连续模 compound die复合模 punched hole冲孔 panel board镶块。to cut edges ...

模具工程常用词汇

die模具 figurefile,chartfile图档 cuttingdie,blankingdie冲裁模 progressivedie,follow on die连续模 compounddie复合模 punchedhole冲孔 panelboard镶块 tocutedges sidecut si...

模具常用词汇

模具分类 injection mold 注塑模 rubber molding 橡胶成形 hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模 multi c ity mold 多模穴模具palletizing die...